Some runs are about pace. Most are about not stopping. Fear No Distance is for the second kind — the long ones, where the distance is the whole point and the finish is a question of patience rather than speed. The numbers Size 18 in wide / 46 cm Steel 3 mm, black powder-coated Bar layout 3 split bars Medal capacity 60+ — tested, not estimated Edge finish Smooth, ribbon-safe Hardware Screws and anchors supplied What the rack holds Capacity is a function of ribbon width: Ribbon Per bar Total Standard 1.5 in 12–14 36–42 Wide 2 in 8–10 24–30 Narrow 1 in 18–20 54–60 Each bar is split, which stops ribbons drifting together. Overlap adds capacity beyond the table — 60+ is a conservative figure. Why 3 mm matters Most racks on the market are cut from 1–1.5 mm sheet. They bow visibly once a collection passes 30 medals, and the sag does not come back out. Three millimetres stays flat under a full load. Installation Fifteen minutes with a drill and a level. Hardware is supplied; the bit size depends on the wall: Stud — 3 mm pilot, screw direct Drywall — 6 mm bit with included anchors Brick — masonry plugs, bought separately Mount the top edge near 60 in from the floor, leaving 20–24 in of clear wall for the medals. Snug the screws rather than overtightening — crushed anchors are the usual reason a rack sags later. What is in the box Medal display rack, 18 in, 3 mm powder-coated steel Screws and wall anchors Mounting instructions Ships from our US warehouse Stocked in Illinois, dispatched within 1 business day on most orders. No customs fees, no international wait. Who it is for Half and full marathoners, ultra runners, trail runners, and anyone who measures a good year in miles rather than minutes. Wall load Expect about 3.5 kg / 8 lb once sixty medals are on it. The included anchors are rated well beyond that. Alongside a shelf This is a medal rack, not a shelf — but it mounts cleanly under one. Leave 8–10 in of gap so ribbons hang free of the shelf edge. Storage that is also display A medal organiser only has to keep things tidy. A wall-mounted display has to be worth looking at. This does both — it takes the collection out of storage without turning it into clutter. Questions we get asked Will it hold my whole collection?60+ medals in most cases. Narrow club ribbons fit close to 60 across the three bars; wide finisher ribbons closer to 30, though medals overlap to add more. What wall can it go on?Stud, drywall or masonry. Screws and drywall anchors are supplied; brick needs masonry plugs bought separately. How durable is the finish?Powder coating is cured under heat, not painted on. The lettering is cut through the metal, so nothing can flake off. Will ribbons fray on the bars?No — all edges are deburred after cutting. I have trophies too — does this work with a shelf?It does. Shelf above, rack below with 8–10 in between, reads as one display. What if I run out of space?Add a second rack alongside. The proportions match, so two look deliberate rather than improvised. Our guarantee Fifteen days to decide. If the display is not what you expected, contact us and we will resolve it. Browse the full medal hanger collection, or the race bib and medal displays if you keep bibs as well as medals.

For the gymnast whose medals go back further than most people’s hobbies Gymnastics starts early and asks a lot — meets on weekends, hours in the gym, seasons that run when other sports have stopped. The medals accumulate over years, and a shoebox does not do that justice. The numbers Size 18 in wide / 46 cm Steel 3 mm, black powder-coated Bar layout 3 split bars Medal capacity 60+ — tested, not estimated Edge finish Smooth, ribbon-safe Hardware Screws and anchors supplied What the rack holds Capacity is a function of ribbon width: Ribbon Per bar Total Standard 1.5 in 12–14 36–42 Wide 2 in 8–10 24–30 Narrow 1 in 18–20 54–60 Each bar is split, which stops ribbons drifting together. Overlap adds capacity beyond the table — 60+ is a conservative figure. Why 3 mm matters Most racks on the market are cut from 1–1.5 mm sheet. They bow visibly once a collection passes 30 medals, and the sag does not come back out. Three millimetres stays flat under a full load. Installation Fifteen minutes with a drill and a level. Hardware is supplied; the bit size depends on the wall: Stud — 3 mm pilot, screw direct Drywall — 6 mm bit with included anchors Brick — masonry plugs, bought separately Mount the top edge near 60 in from the floor, leaving 20–24 in of clear wall for the medals. Snug the screws rather than overtightening — crushed anchors are the usual reason a rack sags later. What is in the box Medal display rack, 18 in, 3 mm powder-coated steel Screws and wall anchors Mounting instructions Ships from our US warehouse Stocked in Illinois, dispatched within 1 business day on most orders. No customs fees, no international wait. Who it is for Artistic and rhythmic gymnasts, tumbling and trampoline athletes, level 3 through elite, coaches, and gymnastics parents. Also works as a club gym wall or an end-of-season team gift. Gymnastics collections grow faster than most Meets award per apparatus as well as all-around, so a single competition can produce four or five medals. Plan for more capacity than the current collection suggests. As a gift Common occasions: a first race, an end-of-season team gift, a graduation, a birthday, Father’s or Mother’s Day, or Christmas for someone who has been quietly accumulating medals in a drawer all year. Free US shipping on orders over $99, so two racks or a rack with sleeves ship free. Organising the wall Split bars make grouping practical: by year, by distance, or by what each race meant. Most people start chronological and switch to distance once the collection passes thirty or so. Nothing is fixed — medals slide on and off without disturbing the ones beside them. Weight and wall load The rack itself weighs about 1.2 lb (550 g). Loaded with sixty medals it reaches roughly 8 lb (3.5 kg) in total — comfortably within the rating of the supplied drywall anchors, and nowhere near the limit if you catch a stud. Questions we get asked Will it hold my whole collection?60+ medals in most cases. Narrow club ribbons fit close to 60 across the three bars; wide finisher ribbons closer to 30, though medals overlap to add more. What wall can it go on?Stud, drywall or masonry. Screws and drywall anchors are supplied; brick needs masonry plugs bought separately. How durable is the finish?Powder coating is cured under heat, not painted on. The lettering is cut through the metal, so nothing can flake off. Will ribbons fray on the bars?No — all edges are deburred after cutting. I have trophies too — does this work with a shelf?It does. Shelf above, rack below with 8–10 in between, reads as one display. What if I run out of space?Add a second rack alongside. The proportions match, so two look deliberate rather than improvised. Our guarantee Fifteen days to decide. If the display is not what you expected, contact us and we will resolve it. Browse the full medal hanger collection, or the race bib and medal displays if you keep bibs as well as medals.

He believed he could, so he did The line gets printed on a lot of things. Here it is cut through 3 mm of steel, with the proof hanging underneath it. At a glance Overall width 18 in (46 cm) Steel gauge 3 mm, matte black powder coat Hanging bars 3, halved for ribbon separation Holds 60+ medals — tested, not estimated Finish detail Deburred laser-cut edges Fixings Included Medal capacity Ribbon width decides how much fits. Our measured figures: Ribbon width Medals per bar Three bars 1.5 in standard 12–14 36–42 2 in wide 8–10 24–30 1 in narrow 18–20 54–60 Split bars keep ribbons in place rather than letting them gather in the middle. Most collections exceed 60 once medals begin to overlap. Built not to bend A 1.5 mm rack starts to curve somewhere around the thirtieth medal. Three millimetres does not. It is heavier to ship and more expensive to cut, and it is the reason the display still hangs straight in five years. Putting it on the wall Everything needed is in the box. What changes is the wall: Into a stud — 3 mm pilot hole, screw goes straight in Into drywall — 6 mm bit, use the supplied anchors, tap them flush first Into masonry — masonry bit plus plugs, sourced separately Gallery height is around 60 in to the top edge. Allow another 20–24 in below for medals to hang into. You receive One 18 in medal display rack, 3 mm black steel Wall fixings — screws and anchors Fitting instructions Dispatch and delivery Stocked in the United States. Most orders ship the next business day, with no import duties and no international transit time. Who it is for Runners, swimmers, cyclists, martial artists, wrestlers and team athletes at any level. Popular as a gift for a son’s first season, a father who runs, or a milestone birthday. Also available The female version — She Believed She Could So She Did. Gift occasions First race, comeback season, milestone birthday, graduation, Christmas, or a coach’s end-of-year gift to a team. Free US shipping over $99. Where to start Most people begin chronologically and switch to grouping by distance once the collection passes thirty. Both work; the split bars support either without ribbons drifting together. Load Rack: approximately 1.2 lb (550 g). Rack plus sixty medals: around 8 lb (3.5 kg). Well inside what the included anchors are rated for. Common questions What is the real capacity?60+ medals. The variable is ribbon width: 12–14 per bar on standard 1.5-inch ribbon, 8–10 on wide championship ribbon. Does it need a stud?No. Drywall anchors are included and hold a full load. A stud is stronger if one lines up, but it is not required. Is the text printed?No — it is cut straight through the sheet. There is no ink or vinyl to peel. Are the edges safe for ribbons?Yes. Laser-cut and deburred, so nothing catches or frays. Does it work as medal storage as well as display?That is the point — wall mounting keeps medals untangled and unscratched, which a drawer does not. Can I add a second rack later?Yes, they are designed to hang side by side at matching heights. If it is not right You have 15 days. Message us and we will make it right — replacement or refund, your choice. Browse the full medal hanger collection, or the race bib and medal displays if you keep bibs as well as medals.

I crossed the line Four words that mean two things at once — the finish line you crossed, and the line in your head you decided not to stop at. Whichever one you had in mind when you signed up, the medals came after. At a glance Overall width 18 in (46 cm) Steel gauge 3 mm, matte black powder coat Hanging bars 3, halved for ribbon separation Holds 60+ medals — tested, not estimated Finish detail Deburred laser-cut edges Fixings Included Medal capacity Ribbon width decides how much fits. Our measured figures: Ribbon width Medals per bar Three bars 1.5 in standard 12–14 36–42 2 in wide 8–10 24–30 1 in narrow 18–20 54–60 Split bars keep ribbons in place rather than letting them gather in the middle. Most collections exceed 60 once medals begin to overlap. Built not to bend A 1.5 mm rack starts to curve somewhere around the thirtieth medal. Three millimetres does not. It is heavier to ship and more expensive to cut, and it is the reason the display still hangs straight in five years. Putting it on the wall Everything needed is in the box. What changes is the wall: Into a stud — 3 mm pilot hole, screw goes straight in Into drywall — 6 mm bit, use the supplied anchors, tap them flush first Into masonry — masonry bit plus plugs, sourced separately Gallery height is around 60 in to the top edge. Allow another 20–24 in below for medals to hang into. You receive One 18 in medal display rack, 3 mm black steel Wall fixings — screws and anchors Fitting instructions Dispatch and delivery Stocked in the United States. Most orders ship the next business day, with no import duties and no international transit time. Who it is for Marathoners and half marathoners, first-time finishers, anyone back from an injury year, and the runner who keeps signing up for one more. Gift occasions First race, comeback season, milestone birthday, graduation, Christmas, or a coach’s end-of-year gift to a team. Free US shipping over $99. Where to start Most people begin chronologically and switch to grouping by distance once the collection passes thirty. Both work; the split bars support either without ribbons drifting together. Load Rack: approximately 1.2 lb (550 g). Rack plus sixty medals: around 8 lb (3.5 kg). Well inside what the included anchors are rated for. Common questions What is the real capacity?60+ medals. The variable is ribbon width: 12–14 per bar on standard 1.5-inch ribbon, 8–10 on wide championship ribbon. Does it need a stud?No. Drywall anchors are included and hold a full load. A stud is stronger if one lines up, but it is not required. Is the text printed?No — it is cut straight through the sheet. There is no ink or vinyl to peel. Are the edges safe for ribbons?Yes. Laser-cut and deburred, so nothing catches or frays. Does it work as medal storage as well as display?That is the point — wall mounting keeps medals untangled and unscratched, which a drawer does not. Can I add a second rack later?Yes, they are designed to hang side by side at matching heights. If it is not right You have 15 days. Message us and we will make it right — replacement or refund, your choice. Browse the full medal hanger collection, or the race bib and medal displays if you keep bibs as well as medals.

For the player who spends more mornings on the ice than off it Hockey medals come from 5am ice times, cold rinks, and seasons that run when everyone else has stopped. This is where they go — not in a bag with the shin guards. Build and dimensions Width 46 cm / 18 in Thickness 3 mm steel Finish Matte black powder coat Bars 3, split into halves Capacity 60+ medals — tested, not estimated Included Mounting hardware and instructions How many medals actually fit Capacity depends on ribbon width rather than medal size. Measured in practice: Ribbon type Per bar Across 3 bars Standard race ribbon, 1.5 in 12–14 36–42 Wide championship ribbon, 2 in 8–10 24–30 Thin club ribbon, 1 in 18–20 54–60 Bars are split into halves, so ribbons stay separated instead of bunching toward the centre. Overlapping medals pushes the total well past 60 on most collections. Steel thickness is the whole difference Thin racks — 1 to 1.5 mm — look identical in a photograph and bend within a season. At 3 mm the bar carries a full collection without deflecting, which is why this is the gauge we cut everything from. How it mounts Pre-drilled and supplied with fixings. Match the drill to the wall: Timber stud: 3 mm pilot hole Plasterboard: 6 mm bit, anchors included Brick or block: masonry plugs, purchased separately Around 60 in to the top edge puts it at eye level, with 20–24 in of wall left underneath. Included The rack — 18 in, 3 mm steel, matte black Fixings: screws and anchors Step-by-step mounting guide US stock, US dispatch Held in our Illinois warehouse and sent within one business day. Nothing crosses a border on the way to you, so there are no duties and no delay. Who it is for Youth and adult league players, high school and college teams, goalies, coaches, and hockey parents who have done the drive to the rink more times than they can count. Also available A second hockey design with a maple leaf — Hockey Canada style. What it weighs 1.2 lb / 550 g empty. Around 8 lb / 3.5 kg with sixty medals on it — a load the supplied anchors carry on plasterboard without help from a stud. If you also display trophies A trophy shelf and a medal rack solve different problems. Mounted together — shelf above, rack 8–10 in below — they make a single achievement wall rather than two competing pieces. Out of the drawer Stacked medals scratch and ribbons crease. On separated bars nothing touches, and the collection stops being a storage problem. FAQ How much does it hold?60+ medals. Standard race ribbons fit 12–14 per bar; thicker lanyard-style ribbons 8–10. Drywall or stud?Either. The included anchors are rated for a fully loaded rack on plasterboard; a stud gives extra margin. Can the lettering wear off?No. It is cut through the steel, not printed or applied. Do the bars catch ribbons?No. Edges are laser-cut then deburred, so ribbons rest on smooth steel. Is this display or storage?Both. Medals stay untangled and visible instead of scratching each other in a box. Can it expand?Yes — racks hang side by side, and a second one matches exactly. Satisfaction guarantee Covered for 15 days from delivery. Anything wrong, get in touch and we will fix it. Browse the full medal hanger collection, or the race bib and medal displays if you keep bibs as well as medals.

Hockey. With the leaf. One piece of steel: the word, a maple leaf, and a player mid-stride cut into it. If you grew up with the game — the 6am ice, the rink coffee, the tournament weekends in a town you had never heard of — you know why the leaf belongs on it. Specifications Width 18 in / 46 cm Material 3 mm steel, powder-coated matte black Bars 3, each split into halves Capacity 60+ medals — tested, not estimated Edges Laser-cut and deburred Mounting Pre-drilled, hardware included Capacity, by ribbon width The limit is the ribbon, not the medal. Here is what fits: Ribbon Per bar Total 1.5 in — typical road race 12–14 36–42 2 in — championship and finisher 8–10 24–30 1 in — school and club events 18–20 54–60 Because the bars are halved, ribbons hang in lanes rather than sliding into one pile. Layering medals adds more on top of these figures. About the gauge Three millimetres is roughly double what a budget rack uses. The practical effect: no visible bow at 40, 50 or 60 medals, and no permanent sag once the weight comes off. Mounting Pre-drilled holes, screws and wall anchors are included. Drill sizes by wall type: Stud: 3 mm pilot hole, drive the screw directly. Strongest option. Drywall: 6 mm bit with the supplied anchors, tapped flush before driving. Brick or concrete: masonry bit and plugs, bought separately — drywall anchors will not hold. Hang the top edge at roughly 60 in / 152 cm from the floor and leave 20–24 in of clear wall beneath for the medals. In the package 18-inch medal rack in powder-coated 3 mm steel Mounting hardware Instructions Shipping Every order leaves our Illinois warehouse, usually within a business day. Domestic delivery means no customs paperwork and no surprise charges. Who it is for Minor hockey and house league players, rep and AAA, high school and college teams, goalies, ringette players, adult league regulars, and the hockey parent who has logged more arena hours than anyone will ever thank them for. Shipping to Canada Shipped by courier from our Illinois warehouse. Under CUSMA, courier shipments at this value clear Canadian customs without duty — you pay provincial GST/HST, the same as buying locally, and nothing more. No surprise charges at the door. Also available A hockey design without the leaf — Ice Hockey medal hanger. Giving it Works as a birthday, graduation or Christmas gift, and as an end-of-season present from a coach or team. Free US shipping applies to orders over $99. Sorting By year reads as a timeline. By distance reads as progression. By significance puts the races that mattered in the middle. Pick one before you hang anything — regrouping later is easy but hanging twice is not. Weight The display weighs about 1.2 lb / 550 g on its own, and roughly 8 lb / 3.5 kg fully loaded. Standard drywall anchors handle that; a stud gives extra margin if one lines up. Frequently asked questions How many medals does an 18-inch rack hold?Sixty or more, depending on ribbon width. Standard 1.5-inch race ribbons fit 12–14 per bar; wide championship ribbons around 8–10. Can I mount it on drywall without a stud?Yes. The supplied anchors carry a fully loaded rack. Use a 6 mm bit, tap them flush, and avoid overtightening. Will the finish chip or fade?The lettering is cut through the steel rather than printed, so there is nothing to scratch off. Powder coat is heat-cured and resists chipping far better than paint. Do the edges damage ribbons?No. Every edge is laser-cut and deburred. Can I use it with a trophy shelf?Yes. Mount the shelf above and this rack 8–10 in below, so medals hang clear of the shelf edge. What happens when it fills up?The racks hang side by side. A second one lines up cleanly, and most collections need one eventually. Guarantee Backed by our 15-day satisfaction guarantee. If it is not right, message us and we will sort it out. Browse the full medal hanger collection, or the race bib and medal displays if you keep bibs as well as medals.

Nobody who signs up for one race stays at one There is always another date on the calendar, another distance you have not tried, another course you want to run better. This is the line every runner says to themselves — usually while already registering. Build and dimensions Width 46 cm / 18 in Thickness 3 mm steel Finish Matte black powder coat Bars 3, split into halves Capacity 60+ medals — tested, not estimated Included Mounting hardware and instructions How many medals actually fit Capacity depends on ribbon width rather than medal size. Measured in practice: Ribbon type Per bar Across 3 bars Standard race ribbon, 1.5 in 12–14 36–42 Wide championship ribbon, 2 in 8–10 24–30 Thin club ribbon, 1 in 18–20 54–60 Bars are split into halves, so ribbons stay separated instead of bunching toward the centre. Overlapping medals pushes the total well past 60 on most collections. Steel thickness is the whole difference Thin racks — 1 to 1.5 mm — look identical in a photograph and bend within a season. At 3 mm the bar carries a full collection without deflecting, which is why this is the gauge we cut everything from. How it mounts Pre-drilled and supplied with fixings. Match the drill to the wall: Timber stud: 3 mm pilot hole Plasterboard: 6 mm bit, anchors included Brick or block: masonry plugs, purchased separately Around 60 in to the top edge puts it at eye level, with 20–24 in of wall left underneath. Included The rack — 18 in, 3 mm steel, matte black Fixings: screws and anchors Step-by-step mounting guide US stock, US dispatch Held in our Illinois warehouse and sent within one business day. Nothing crosses a border on the way to you, so there are no duties and no delay. Who it is for Runners whose race calendar keeps growing, plus triathletes, swimmers and cyclists who will read the message the same way. Plan for the collection you will have Given the message, size the display for three years out rather than today. The racks hang side by side if a second one becomes necessary. Trophy shelf compatible If trophies and plaques are part of the collection, mount a shelf above this rack with 8–10 in between. Nothing overlaps and the whole wall reads as deliberate. Beyond a storage box Most medal storage means a drawer, a shoebox or a tangle in a wardrobe. Wall mounting solves the tangle and the forgetting at the same time, and the medals stop scratching each other. As a gift Common occasions: a first race, an end-of-season team gift, a graduation, a birthday, Father’s or Mother’s Day, or Christmas for someone who has been quietly accumulating medals in a drawer all year. Free US shipping on orders over $99, so two racks or a rack with sleeves ship free. FAQ How much does it hold?60+ medals. Standard race ribbons fit 12–14 per bar; thicker lanyard-style ribbons 8–10. Drywall or stud?Either. The included anchors are rated for a fully loaded rack on plasterboard; a stud gives extra margin. Can the lettering wear off?No. It is cut through the steel, not printed or applied. Do the bars catch ribbons?No. Edges are laser-cut then deburred, so ribbons rest on smooth steel. Is this display or storage?Both. Medals stay untangled and visible instead of scratching each other in a box. Can it expand?Yes — racks hang side by side, and a second one matches exactly. Satisfaction guarantee Covered for 15 days from delivery. Anything wrong, get in touch and we will fix it. Browse the full medal hanger collection, or the race bib and medal displays if you keep bibs as well as medals.

Not faster. Not further. Just forward. On the hard weeks that is the only instruction that helps. Progress is not always a personal best — sometimes it is showing up when you would rather not. Every medal on this rack is a week you kept going. Build and dimensions Width 46 cm / 18 in Thickness 3 mm steel Finish Matte black powder coat Bars 3, split into halves Capacity 60+ medals — tested, not estimated Included Mounting hardware and instructions How many medals actually fit Capacity depends on ribbon width rather than medal size. Measured in practice: Ribbon type Per bar Across 3 bars Standard race ribbon, 1.5 in 12–14 36–42 Wide championship ribbon, 2 in 8–10 24–30 Thin club ribbon, 1 in 18–20 54–60 Bars are split into halves, so ribbons stay separated instead of bunching toward the centre. Overlapping medals pushes the total well past 60 on most collections. Steel thickness is the whole difference Thin racks — 1 to 1.5 mm — look identical in a photograph and bend within a season. At 3 mm the bar carries a full collection without deflecting, which is why this is the gauge we cut everything from. How it mounts Pre-drilled and supplied with fixings. Match the drill to the wall: Timber stud: 3 mm pilot hole Plasterboard: 6 mm bit, anchors included Brick or block: masonry plugs, purchased separately Around 60 in to the top edge puts it at eye level, with 20–24 in of wall left underneath. Included The rack — 18 in, 3 mm steel, matte black Fixings: screws and anchors Step-by-step mounting guide US stock, US dispatch Held in our Illinois warehouse and sent within one business day. Nothing crosses a border on the way to you, so there are no duties and no delay. Who it is for Athletes across any sport, and particularly those training back from injury or in the middle of a long build. Running out of space? The racks are designed to hang side by side. If a collection outgrows one, a second matches up cleanly — see the full medal hanger collection. What it weighs 1.2 lb / 550 g empty. Around 8 lb / 3.5 kg with sixty medals on it — a load the supplied anchors carry on plasterboard without help from a stud. If you also display trophies A trophy shelf and a medal rack solve different problems. Mounted together — shelf above, rack 8–10 in below — they make a single achievement wall rather than two competing pieces. Out of the drawer Stacked medals scratch and ribbons crease. On separated bars nothing touches, and the collection stops being a storage problem. FAQ How much does it hold?60+ medals. Standard race ribbons fit 12–14 per bar; thicker lanyard-style ribbons 8–10. Drywall or stud?Either. The included anchors are rated for a fully loaded rack on plasterboard; a stud gives extra margin. Can the lettering wear off?No. It is cut through the steel, not printed or applied. Do the bars catch ribbons?No. Edges are laser-cut then deburred, so ribbons rest on smooth steel. Is this display or storage?Both. Medals stay untangled and visible instead of scratching each other in a box. Can it expand?Yes — racks hang side by side, and a second one matches exactly. Satisfaction guarantee Covered for 15 days from delivery. Anything wrong, get in touch and we will fix it. Browse the full medal hanger collection, or the race bib and medal displays if you keep bibs as well as medals.

Miles of memories A long running history is not a list of times. It is a set of days you can still describe — weather, company, the point where it got hard, the point where it stopped being hard. The medals are the index. Specifications Width 18 in / 46 cm Material 3 mm steel, powder-coated matte black Bars 3, each split into halves Capacity 60+ medals — tested, not estimated Edges Laser-cut and deburred Mounting Pre-drilled, hardware included Capacity, by ribbon width The limit is the ribbon, not the medal. Here is what fits: Ribbon Per bar Total 1.5 in — typical road race 12–14 36–42 2 in — championship and finisher 8–10 24–30 1 in — school and club events 18–20 54–60 Because the bars are halved, ribbons hang in lanes rather than sliding into one pile. Layering medals adds more on top of these figures. About the gauge Three millimetres is roughly double what a budget rack uses. The practical effect: no visible bow at 40, 50 or 60 medals, and no permanent sag once the weight comes off. Mounting Pre-drilled holes, screws and wall anchors are included. Drill sizes by wall type: Stud: 3 mm pilot hole, drive the screw directly. Strongest option. Drywall: 6 mm bit with the supplied anchors, tapped flush before driving. Brick or concrete: masonry bit and plugs, bought separately — drywall anchors will not hold. Hang the top edge at roughly 60 in / 152 cm from the floor and leave 20–24 in of clear wall beneath for the medals. In the package 18-inch medal rack in powder-coated 3 mm steel Mounting hardware Instructions Shipping Every order leaves our Illinois warehouse, usually within a business day. Domestic delivery means no customs paperwork and no surprise charges. Who it is for Runners with years behind them rather than months. Works well as a milestone gift: a hundredth race, a fiftieth birthday, a final marathon before switching to shorter distances. Trophies as well as medals? Hang a trophy shelf above and this rack 8–10 in beneath. The shelf carries what stands; the rack carries what hangs. Together they read as one wall. Organising, not just displaying Wall mounting is the only medal storage that does not involve untangling something first. Separated bars, nothing stacked, nothing abrading. Bought as a present? Motto designs are the safer choice when you do not know the sport. Sport-specific designs land better when you do. Free US shipping applies over $99. Frequently asked questions How many medals does an 18-inch rack hold?Sixty or more, depending on ribbon width. Standard 1.5-inch race ribbons fit 12–14 per bar; wide championship ribbons around 8–10. Can I mount it on drywall without a stud?Yes. The supplied anchors carry a fully loaded rack. Use a 6 mm bit, tap them flush, and avoid overtightening. Will the finish chip or fade?The lettering is cut through the steel rather than printed, so there is nothing to scratch off. Powder coat is heat-cured and resists chipping far better than paint. Do the edges damage ribbons?No. Every edge is laser-cut and deburred. Can I use it with a trophy shelf?Yes. Mount the shelf above and this rack 8–10 in below, so medals hang clear of the shelf edge. What happens when it fills up?The racks hang side by side. A second one lines up cleanly, and most collections need one eventually. Guarantee Backed by our 15-day satisfaction guarantee. If it is not right, message us and we will sort it out. Browse the full medal hanger collection, or the race bib and medal displays if you keep bibs as well as medals.

Never again Two words that mean whatever you need them to mean. Never again quitting at kilometre eight. Never again a season on the couch. Never again wondering what would have happened if you had entered. The medals underneath are what happened instead. Specifications Width 18 in / 46 cm Material 3 mm steel, powder-coated matte black Bars 3, each split into halves Capacity 60+ medals — tested, not estimated Edges Laser-cut and deburred Mounting Pre-drilled, hardware included Capacity, by ribbon width The limit is the ribbon, not the medal. Here is what fits: Ribbon Per bar Total 1.5 in — typical road race 12–14 36–42 2 in — championship and finisher 8–10 24–30 1 in — school and club events 18–20 54–60 Because the bars are halved, ribbons hang in lanes rather than sliding into one pile. Layering medals adds more on top of these figures. About the gauge Three millimetres is roughly double what a budget rack uses. The practical effect: no visible bow at 40, 50 or 60 medals, and no permanent sag once the weight comes off. Mounting Pre-drilled holes, screws and wall anchors are included. Drill sizes by wall type: Stud: 3 mm pilot hole, drive the screw directly. Strongest option. Drywall: 6 mm bit with the supplied anchors, tapped flush before driving. Brick or concrete: masonry bit and plugs, bought separately — drywall anchors will not hold. Hang the top edge at roughly 60 in / 152 cm from the floor and leave 20–24 in of clear wall beneath for the medals. In the package 18-inch medal rack in powder-coated 3 mm steel Mounting hardware Instructions Shipping Every order leaves our Illinois warehouse, usually within a business day. Domestic delivery means no customs paperwork and no surprise charges. Who it is for Athletes across any sport — runners, swimmers, cyclists, martial artists, gymnasts, dancers and team players. From storage to display Medals kept in a box scratch, tangle and get forgotten. Wall-mounted, they take no floor space, stay untangled, and stop being a storage problem entirely. Buying it as a gift It sells well for graduations, birthdays, Christmas and end-of-season awards nights. If you are buying for someone whose sport you are not sure about, choose a motto design rather than a sport-specific one. Orders over $99 ship free within the US. Grouping the collection Split bars mean you can section the wall rather than fill it. Group by season, by distance, or by the races that changed something. Medals lift off individually, so nothing is locked in. Frequently asked questions How many medals does an 18-inch rack hold?Sixty or more, depending on ribbon width. Standard 1.5-inch race ribbons fit 12–14 per bar; wide championship ribbons around 8–10. Can I mount it on drywall without a stud?Yes. The supplied anchors carry a fully loaded rack. Use a 6 mm bit, tap them flush, and avoid overtightening. Will the finish chip or fade?The lettering is cut through the steel rather than printed, so there is nothing to scratch off. Powder coat is heat-cured and resists chipping far better than paint. Do the edges damage ribbons?No. Every edge is laser-cut and deburred. Can I use it with a trophy shelf?Yes. Mount the shelf above and this rack 8–10 in below, so medals hang clear of the shelf edge. What happens when it fills up?The racks hang side by side. A second one lines up cleanly, and most collections need one eventually. Guarantee Backed by our 15-day satisfaction guarantee. If it is not right, message us and we will sort it out. Browse the full medal hanger collection, or the race bib and medal displays if you keep bibs as well as medals.

Three words, at full width No silhouette, no subtitle — just the instruction, in the largest lettering we cut. The medals underneath are what happens when someone actually follows it. At a glance Overall width 18 in (46 cm) Steel gauge 3 mm, matte black powder coat Hanging bars 3, halved for ribbon separation Holds 60+ medals — tested, not estimated Finish detail Deburred laser-cut edges Fixings Included Medal capacity Ribbon width decides how much fits. Our measured figures: Ribbon width Medals per bar Three bars 1.5 in standard 12–14 36–42 2 in wide 8–10 24–30 1 in narrow 18–20 54–60 Split bars keep ribbons in place rather than letting them gather in the middle. Most collections exceed 60 once medals begin to overlap. Built not to bend A 1.5 mm rack starts to curve somewhere around the thirtieth medal. Three millimetres does not. It is heavier to ship and more expensive to cut, and it is the reason the display still hangs straight in five years. Putting it on the wall Everything needed is in the box. What changes is the wall: Into a stud — 3 mm pilot hole, screw goes straight in Into drywall — 6 mm bit, use the supplied anchors, tap them flush first Into masonry — masonry bit plus plugs, sourced separately Gallery height is around 60 in to the top edge. Allow another 20–24 in below for medals to hang into. You receive One 18 in medal display rack, 3 mm black steel Wall fixings — screws and anchors Fitting instructions Dispatch and delivery Stocked in the United States. Most orders ship the next business day, with no import duties and no international transit time. Who it is for Athletes across any sport. A safe choice as a gift when you do not know which discipline to buy for. Also available A version with a second line — Never Give Up, Challenge Your Limits. Storage that is also display A medal organiser only has to keep things tidy. A wall-mounted display has to be worth looking at. This does both — it takes the collection out of storage without turning it into clutter. Occasions First race, comeback season, graduation, milestone birthday, Christmas, awards night. Free US shipping on orders over $99. Layout options Because each bar is split into halves, you can section the display instead of filling it end to end. Common groupings: Chronological, oldest to newest By event type — road, trail, track, championship By distance, shortest at the top Medals lift on and off individually, so the arrangement is not permanent. Common questions What is the real capacity?60+ medals. The variable is ribbon width: 12–14 per bar on standard 1.5-inch ribbon, 8–10 on wide championship ribbon. Does it need a stud?No. Drywall anchors are included and hold a full load. A stud is stronger if one lines up, but it is not required. Is the text printed?No — it is cut straight through the sheet. There is no ink or vinyl to peel. Are the edges safe for ribbons?Yes. Laser-cut and deburred, so nothing catches or frays. Does it work as medal storage as well as display?That is the point — wall mounting keeps medals untangled and unscratched, which a drawer does not. Can I add a second rack later?Yes, they are designed to hang side by side at matching heights. If it is not right You have 15 days. Message us and we will make it right — replacement or refund, your choice. Browse the full medal hanger collection, or the race bib and medal displays if you keep bibs as well as medals.

When you run, it is not the giant steps that count It is the small ones, repeated. A female runner silhouette cut mid-stride through the steel — the design says which sport and who runs it, and leaves the rest to the medals underneath. At a glance Overall width 18 in (46 cm) Steel gauge 3 mm, matte black powder coat Hanging bars 3, halved for ribbon separation Holds 60+ medals — tested, not estimated Finish detail Deburred laser-cut edges Fixings Included Medal capacity Ribbon width decides how much fits. Our measured figures: Ribbon width Medals per bar Three bars 1.5 in standard 12–14 36–42 2 in wide 8–10 24–30 1 in narrow 18–20 54–60 Split bars keep ribbons in place rather than letting them gather in the middle. Most collections exceed 60 once medals begin to overlap. Built not to bend A 1.5 mm rack starts to curve somewhere around the thirtieth medal. Three millimetres does not. It is heavier to ship and more expensive to cut, and it is the reason the display still hangs straight in five years. Putting it on the wall Everything needed is in the box. What changes is the wall: Into a stud — 3 mm pilot hole, screw goes straight in Into drywall — 6 mm bit, use the supplied anchors, tap them flush first Into masonry — masonry bit plus plugs, sourced separately Gallery height is around 60 in to the top edge. Allow another 20–24 in below for medals to hang into. You receive One 18 in medal display rack, 3 mm black steel Wall fixings — screws and anchors Fitting instructions Dispatch and delivery Stocked in the United States. Most orders ship the next business day, with no import duties and no international transit time. Who it is for Women and girls who race at any distance — parkrun regulars, 5K and 10K runners, half and full marathoners, trail and ultra runners. Works for a first race, a comeback season or a milestone birthday. Also available The same design with a male runner silhouette. Arranging your collection The staggered bars let you group rather than just fill: By year — one bar per season, so progress reads left to right By distance — shorter races on the top bar, longer ones below By significance — the races that mattered in the centre, everything else around them Ribbons hang in lanes rather than sliding together, so regrouping later takes a minute rather than an afternoon. Loaded weight Roughly 8 lb (3.5 kg) fully loaded, of which the rack itself is 1.2 lb (550 g). Nothing that troubles standard drywall fixings. Trophies as well as medals? Hang a trophy shelf above and this rack 8–10 in beneath. The shelf carries what stands; the rack carries what hangs. Together they read as one wall. Common questions What is the real capacity?60+ medals. The variable is ribbon width: 12–14 per bar on standard 1.5-inch ribbon, 8–10 on wide championship ribbon. Does it need a stud?No. Drywall anchors are included and hold a full load. A stud is stronger if one lines up, but it is not required. Is the text printed?No — it is cut straight through the sheet. There is no ink or vinyl to peel. Are the edges safe for ribbons?Yes. Laser-cut and deburred, so nothing catches or frays. Does it work as medal storage as well as display?That is the point — wall mounting keeps medals untangled and unscratched, which a drawer does not. Can I add a second rack later?Yes, they are designed to hang side by side at matching heights. If it is not right You have 15 days. Message us and we will make it right — replacement or refund, your choice. Browse the full medal hanger collection, or the race bib and medal displays if you keep bibs as well as medals.